Videotek TVM-4DG Multiformat HD/SD-SDI Waveform Monitor/Vectorscope
The TVM-4DG multiformat waveform monitor/vectorscope is an easy-to-operate tool for monitoring HD-SDI (1080 and 720) and SD-SDI (525 and 625) signals and is housed in a convenient half-rack scope package. The display can show any one of the following: waveform, vector, picture or Videotek® patented timing display. Hard Travel case and rack mount sold separately.
SPECIFICATIONS
Specifications and designs are subject to change without notice
Video
Inputs A and B (Digital) 1080i/60, 1080i/59.94, 1080i/50, 1080p/30, 1080p/29.97, 1080p/25, 1080p/24,1080p/23.98, 1080p/30sF, 1080p/29.97sF, 1080p/25sF, 1080p/24sF, 1080p/23.98sF, 720p/60, 720p/59.94, 720p/50, 720p/30, 720p/29.97, 720p/24, 720p/23.98, 525/59.94 or 625/50 auto-detect
Data Rate 1.485 Gb/s, 270 Mb/s auto-detect
Level 800 mV, nominal
Return Loss =-15 dB, 5 MHz to 1.485 GHz
Connectors 4 BNC, Hi-Z looping
Reference
Input NTSC/PAL blackburst or composite video, tri-level sync auto-detect (per SMPTE 274M)
Signal Level NTSC: blackburst 286 mV pk-pk ± 6 dB
PAL: sync and burst 300 mV pk-pk ± 6 dB
Tri-level: 600 mV pk-pk ± 3 dB
Connectors. 2 BNC, Hi-Z looping
Return Loss =-40 dB, 100 kHz to 5 MHz
Control
GPI Input selection, function selection, momentary closure
Input Impedance 10 k ohms returned to + 5 V
Connector 15-pin D-sub female
VFLASH Ethernet port for firmware updates
Display
General Picture, waveform, vector or timing
Waveform YCbCr, RGB, YRGB, Digital as composite
Sweep Time Base 1 H, 2 H or 3 H with x1, x5, x10 magnification
1 V, 2 V or 3 V with x1, x5, x10, x25 magnification
Waveform Accuracy ± 1%
Vector Cr vs. Cb
Vector Accuracy ± 1°
Power Requirements
Power Input 90 to 260 V AC, 50/60 Hz, nominal
Mechanical
Dimensions H x W x D 5.25 x 8.25 x 16.63 in. (13.34 x 21.6 x 42.24 cm)
Environmental
Operating Temperature 0° to 50° C
Storage Temperature -40° to 65° C
Humidity 90% maximum (non-condensing)
Operating Altitude To 10,000 ft (3,050 m) above sea level
Standard Accessories
Operators manual
GPI breakout
Please Note, this unit ships standard with US power cord. Specify UK, EURO or Austrailian power cord if needed, when ordering.
FEATURES
- Two passive looping HD/SD-SDI inputs with auto-detection of input format
- External reference input accepts blackburst or tri-level sync
- Simple operation
- On-screen display of picture, waveform, vector or timing
- GPI control of input and function selection
- Standards supported: SMPTE 292M, SMPTE 259M-C
SPECIFICATIONS
Specifications and designs are subject to change without notice
Video
Inputs A and B (Digital) 1080i/60, 1080i/59.94, 1080i/50, 1080p/30, 1080p/29.97, 1080p/25, 1080p/24,1080p/23.98, 1080p/30sF, 1080p/29.97sF, 1080p/25sF, 1080p/24sF, 1080p/23.98sF, 720p/60, 720p/59.94, 720p/50, 720p/30, 720p/29.97, 720p/24, 720p/23.98, 525/59.94 or 625/50 auto-detect
Data Rate 1.485 Gb/s, 270 Mb/s auto-detect
Level 800 mV, nominal
Return Loss =-15 dB, 5 MHz to 1.485 GHz
Connectors 4 BNC, Hi-Z looping
Reference
Input NTSC/PAL blackburst or composite video, tri-level sync auto-detect (per SMPTE 274M)
Signal Level NTSC: blackburst 286 mV pk-pk ± 6 dB
PAL: sync and burst 300 mV pk-pk ± 6 dB
Tri-level: 600 mV pk-pk ± 3 dB
Connectors. 2 BNC, Hi-Z looping
Return Loss =-40 dB, 100 kHz to 5 MHz
Control
GPI Input selection, function selection, momentary closure
Input Impedance 10 k ohms returned to + 5 V
Connector 15-pin D-sub female
VFLASH Ethernet port for firmware updates
Display
General Picture, waveform, vector or timing
Waveform YCbCr, RGB, YRGB, Digital as composite
Sweep Time Base 1 H, 2 H or 3 H with x1, x5, x10 magnification
1 V, 2 V or 3 V with x1, x5, x10, x25 magnification
Waveform Accuracy ± 1%
Vector Cr vs. Cb
Vector Accuracy ± 1°
Power Requirements
Power Input 90 to 260 V AC, 50/60 Hz, nominal
Mechanical
Dimensions H x W x D 5.25 x 8.25 x 16.63 in. (13.34 x 21.6 x 42.24 cm)
Environmental
Operating Temperature 0° to 50° C
Storage Temperature -40° to 65° C
Humidity 90% maximum (non-condensing)
Operating Altitude To 10,000 ft (3,050 m) above sea level
Standard Accessories
Operators manual
GPI breakout
Please Note, this unit ships standard with US power cord. Specify UK, EURO or Austrailian power cord if needed, when ordering.
